![]() But as you see, we are talking about hours off, especially during night when you dont use your phoneĬode: Select all 18:04:15 wireless,info connected, signal strength -66ġ8:25:15 wireless,info disconnected, connection lost, sigġ8:30:52 wireless,info connected, signal strength -61ġ8:48:31 wireless,info disconnected, connection lost, sigġ8:48:46 wireless,info connected, signal strength -58ġ8:53:42 wireless,info disconnected, connection lost, sigġ8:54:49 wireless,info connected, signal strength -62ġ9:00:23 wireless,info disconnected, connection lost, sigġ9:00:32 wireless,info connected, signal strength -61ġ9:06:19 wireless,info disconnected, connection lost, sigġ9:07:25 wireless,info connected, signal strength -62ġ9:12:31 wireless,info disconnected, connection lost, sigġ9:12:49 wireless,info connected, signal strength -62ġ9:18:03 wireless,info disconnected, connection lost, signal strenght -63 ![]() The away status appears 180seconds after disconnecting from WiFi, so roaming between 2.4 and 5ghz also doesnt make problems. I have signal fair enough, and the devices connecting to network immediately you wake them up (phone, tablets etc.) but during "locked" status, they are randomly disconnected, i have missed WiFi calls, and as you see, my smarthome system (with mikrotik integration) is capturing phone state as "away", while the android phone is "home" all the time (see on huge screenshots.). The phone behaves like described also if its lying locked 2meters on the table from router, so ill think it is not about signal strenght or not connecting. Since ax3 uses only new driver, i have no choice, and really no clue what else can i do. If i made try with wifiwave2 i had to revert back, also because of this issue. The case is, that generic driver on hap ac3 worked without issues, with "same" config. Ill make next time pictures smaller, in case of posting them. Ive posted the pictures as attachments immediately after screenshots was made to provide as much informations as i can. Exactly this is how i expect to behave and reply, if somebody made a mistake or need help. Thank you very much - Thank you for your reply. I found lot of informations from the past, set beacon, etc., but the issue is still there.Ĭan you please help me, what else can i do ? ![]() Have still some "ac" MikroTik devices in garden, also everything works as should. Im using those smarthome automations and WiFi calling (because of poor GSM) for years, and with generic driver on hap ac3 worked everything without problems. Im posting my configuration and also screenshots of smarthome presence history, also comparison to an Android phone (which works great). It looks like some energy/powersavings kicks in on end devices, and the results are missed WiFi calls and not working smarthome automations based on presence (presence measured-automated by WiFi connection of our phones). I would like to kindly ask you for help, since i have serious problems after upgrading from "hap ac3 / generic WiFi" to "hap ax3 /wifiwave2" and my Apple devices. ![]() Since my troubles are also related to Apple products, i try to ask here instead of creating new topic. Set contact=GW enabled=yes location=GW trap-community=GWSNMP trap-version=2 Set allow-remote-requests=yes servers=1.1.1.1,8.8.8.8Īdd action=drop chain=input src-address=36.110.228.0/24Īdd action=masquerade chain=srcnat out-interface=ether1 src-address=\ Set band=5ghz-a/n/ac disabled=no frequency=5240 \ Security-profile=GW ssid="#" wmm-support=enabled Set band=2ghz-g/n country="united states3" \ĭisabled=no frequency=2462 installation=indoor mode=ap-bridge \ Set supplicant-identity=MikroTikĪdd authentication-types=wpa2-psk,wpa2-eap eap-methods="" group-key-update=\ġ5m mode=dynamic-keys name=GW supplicant-identity="" wpa-pre-shared-key=\
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |